m5stack

Flash a Cardputer-Adv and install the Claude Buddy apps in one command.

Quick start

1. Clone this repo locally — anywhere is fine:

   git clone 
   

   The skill auto-detects the buddy bundle relative to its own install location, so the clone path doesn’t matter. ~/Downloads/m5stack/ and ~/Desktop/m5stack/ are also checked as conventional fallbacks.
2. Plug the Cardputer into your laptop via USB-C
3. Open Claude Code and start a new chat
4. Point Claude Code to the repo folder
5. Type m5-onboard go

That’s it — Claude will automatically flash the firmware and push the apps onto the device.

When Claude prompts you to put the device into download mode

Halfway through, Claude will pause and ask you to do this on the back of the device:

1. Hold down the G0 button on the Cardputer
2. While still holding G0, press the Reset button
3. Release Reset first, then release G0
4. The screen goes dark — device is in download mode

Claude takes over from there.

What happens next

• Firmware writes to the device (~180 seconds)
• Apps push to the device (~100 seconds)
• Device reboots straight into the launcher — pick an app and go

Done. Power the device on/off with the side switch.

---

Using Claude Buddy (BLE)

1. Power on the Cardputer
2. Pick Claude Buddy from the launcher menu
3. In Claude Desktop: Help → Troubleshooting → Enable Developer Tools (one-time, persists)
4. Then Developer menu → Hardware Buddy → Connect

Event WiFi

The bundled launcher auto-connects to the event WiFi (cardputer / cardconnect) on every boot and displays the result on screen — Connected · IP: 192.168.x.x on success, WiFi: offline on failure (the launcher always continues either way). The credentials are intentionally checked into buddy/device/wifi_event.py; the AP is publicly broadcast at the venue and the password is the published handout, so this is not a leaked secret. To use this bundle outside the event, edit wifi_event.py (replace SSID/PASSWORD) or remove the _connect_wifi_with_splash() call near the top of main() to disable the auto-connect entirely.

Adding your own app

1. Drop a .py file into buddy/device/apps/
2. Push just the apps without re-flashing:

   python3 .claude/skills/m5-onboard/scripts/install_apps.py --port  --src buddy
   

3. The launcher auto-discovers the new app on next boot

Crib from buddy/device/apps/hello_cardputer.py — it’s the smallest example of the conventions (keyboard polling, font, exit behaviour).

Getting back to stock UIFlow

The buddy bundle takes over the boot flow via /flash/main.py. Remove that file and UIFlow’s stock launcher boots normally on the next reset. From the device REPL:

import os
os.remove('/flash/main.py')
import machine; machine.reset()

To also drop the apps under /flash/apps/, walk that directory the same way and remove what you don’t want.

If you want a fresh UIFlow firmware on top, re-run m5-onboard go without --apps: the skill flashes UIFlow and stops, leaving the filesystem alone. The previous boot_uiflow.py-rename procedure here referred to a backup that install_apps.py only creates when the bundle ships its own root boot.py; the buddy bundle doesn’t, so that backup never exists for these users.

---

Prerequisites

You need Python 3.10+, git, and Claude Code on your laptop. pyserial ships vendored inside .claude/skills/m5-onboard/scripts/vendor/. esptool is GPL-licensed and is not vendored — the skill auto-installs it via pip on first run if it isn’t already in your environment, so the user-facing experience is still a single command. To pre-install explicitly: python3 -m pip install --user -r requirements.txt.

Bootstrap if needed:

• macOS — python3 usually pre-installed; if not, brew install python
• Linux (Debian/Ubuntu) — sudo apt-get install -y python3 python3-pip git
• Windows — winget install -e --id Python.Python.3.13 and winget install -e --id Git.Git

Windows + older boards only: the CH9102 USB-UART driver is needed for Basic / Fire / Core2 / StickC. Download from WCH. Cardputer-Adv and CoreS3 use the in-box composite-USB driver and need nothing extra.

Want --apps buddy to point at a different bundle? The default resolves to the buddy/device/ directory next to the skill in this repo, with ~/Downloads/m5stack/ and ~/Desktop/m5stack/ checked as fallbacks. To override (e.g. you maintain a fork or have a customized bundle elsewhere), set M5_BUDDY_DIR:

export M5_BUDDY_DIR=/path/to/buddy/device

Troubleshooting

• Download-mode prompt keeps retrying — you’re releasing G0 too early. Release Reset first, keep holding G0 for about a second, then release.
• “No USB-UART bridge found” (older boards) — install the CH9102 driver on Windows; on macOS/Linux, unplug and replug.
• Claude Buddy never connects over BLE — make sure the buddy launcher (not UIFlow’s) owns /flash/main.py. The skill handles this automatically on install.
• Something else feels broken — run python3 .claude/skills/m5-onboard/scripts/smoke_test.py --port for an I2C + LCD + speaker + button check.

What’s in this repo

• .claude/skills/m5-onboard/ — the Claude Code skill. Detect port, flash UIFlow, install apps. See .claude/skills/m5-onboard/SKILL.md for the full playbook and every gotcha baked into the scripts.
• buddy/ — the MicroPython app bundle that gets installed. See buddy/README.md for device-side layout and iteration tooling.

The two are decoupled by design: the m5-onboard skill can install any bundle via --apps ; buddy is just what ships here.

License

This project’s own code is licensed under Apache 2.0 — see LICENSE and NOTICE.

pyserial (BSD-3-Clause, Apache-compatible) is the only third-party package bundled in .claude/skills/m5-onboard/scripts/vendor/. esptool (GPLv2+) is intentionally not vendored; it’s declared as a pip dependency in requirements.txt so the repository itself stays cleanly Apache-2.0. See LICENSE-THIRD-PARTY.md for details.